Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

高频脉管制冷机的研究进展(下)

介绍了斯特林脉管制冷机(高频脉管制冷机)国内外最新研究现状以及发展趋势。分析了由于高频脉管制冷机的效率可以达到甚至超过斯特林制冷机,从而在空间领域、红外传感器件和高温超导器件的冷却领域获得广泛应用。指出了线性压缩机是高频脉管制冷机的重要部件之一,提高线性压缩机的性能及机械寿命是提高高频脉管制冷机性能和寿命的一条重要途径。     

幅相一致行波管高频电路CAD研究

 在行波管的设计和装配过程中，各部件的尺寸必须严格控制，高频电路参数的离散对行波管色散特性有极大的影响。使用螺旋导电面模型，模拟计算了高频结构各主要参数离散对色散特性和轴向互作用耦合阻抗的影响。分析计算了夹持杆宽度、翼片高度、螺旋线平均半径、螺距、夹持杆介电常数等离散时对色散特性和轴向互作用耦合阻抗的影响，为新型幅相一致行波管的设计和生产提供了很有价值的参考建议。     

加肋圆柱壳在轴压作用下的屈曲和后屈曲

本文讨论完善和非完善的,纵向加肋和正交加肋圆柱壳在轴压作用下的屈曲和后屈曲性态.依据文[1]提供的圆柱薄壳屈曲的边界层理论及其分析方法,给出了加肋圆柱壳在轴压作用下的屈曲和后屈曲理论分析.本文同时讨论肋骨与壳板材料不同时对加肋圆柱壳屈曲和后屈曲性态的影响.     

The push-out region of an immersed manifold

We consider immersions: and construct a subspace of which corresponds to a set of embedded manifolds which are either parallel to f, tubes around f or, in general, partial tubes around f. This space is invariant under the action of the normal holonomy group, We investigate the case where is non-trivial and obtain some results on the number of connected components of . Received 24 March 2000.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

双面加热环形通道内干涸点的确定

根据环形管通道内流体流动和换热的特点,以Kirillov和Smogalev提出的干涸点理论模型假设为基础,从最基本的质量守恒方程出发,并引入临界液膜厚度等相应的辅助模型,得到了双面加热环形通道内流动沸腾干涸点的理论模型。同时针对间隙为1.0mm和1.5mm的环形窄缝进行了低压低质量流速工况下干涸点的实验研究。比较发现理论模型预测值与实验结果基本相符。说明本文提出的理论模型适用于低压低流量条件下的窄环形通道。实验同时发现:环状流临界热流密度在系统压力为2.2MPa达到最大值,临界含汽量随质量流速的增大呈缓慢下降趋势。     

Stability and Nonlinear Deformation of Cylindrical Grids

The general stability of single-layer cylindrical grids is studied in linear and nonlinear formulations. Dependence of the general buckling load on the geometry and stiffness parameters of a grid is established in an analytical form. Such grids are numerically analyzed for stability. It is established that the general buckling load is much less than the local buckling load. Typical general buckling modes are found. It is shown that such grids are weakly sensitive to imperfections     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

替代柱面透镜的二元光学元件设计

在二极管泵浦固体激光器耦合光学系统中，柱面透镜起着非常重要的作用。随着系统轻量化、小型化的要求需要用重量轻、尺寸小的光学器件来替代。本文介绍一种用于替代柱面透镜的二元光学元件的设计和制作方法。